MICROWAVE POWER EQUIPMENT
SOLID STATE AMPLIFIER SYSTEM
MODEL NO.
PA-44-0-1000/2000
25 WATTS
1000-2000 MHz
CLASS A LINEAR
INTRODUCTION
The MPE Model No. PA-44-0-1000/2000 is a solid
state wide band linear power amplifier operating in the class A linear mode with a power
level of 25 watts CW/PEP, from 1000-2000 MHz. The amplifier system will amplify CW, AM,
pulse, FM and phase modulated signals with minimal distortion to very high power levels.
All operating controls and monitoring are accessible from the front panel.
The amplifier is housed in a 19" rackmount case
with its own internal power supply, forced-air cooling and ALC (Automatic Level Control)
leveling loop. The input and output impedances are 50 ohms and the unit may be driven to
full power output by most RF synthesizers, signal generators and swept signal sources.
The amplifier system is fully protected against
input overdrive, temperature and output load VSWR conditions. Both the integral high
efficiency power supply and forced-air cooling systems are conservatively designed to
permit operation over all normal operating conditions.
The internal leveling mode of operation (front panel
selectable) allows the amplifier output to be leveled (+0.5 dB) with any signal
generator or sweeper. The front panel power level control provides a leveled RF power
output over a 30 dB dynamic range. In the ALC OFF mode of operation, the output power is a
function of the input level. Output power, both forward and reflected, is displayed in
watts on a front panel numerical display.
The amplifier is modular constructed for ease of
maintainability. All RF modules are designed with a 50 ohm input and output impedance. In
the event of a resistor failure, that particular module can be field replaced without the
need for special RF test equipment.
ELECTRICAL AND MECHANICAL SPECIFICATIONS
| Frequency Range |
1000-2000 MHz |
| Class of Operation |
A Linear |
| Forward Power Output |
25 Watts CW/PEP |
| Forward Power Output Flatness Over Frequency Range (ALC
Loop) |
30 dB, Min. |
| Load Impedance |
50 Ohms, Nom. |
| Load VSWR, Protection |
Isolator Protected into infinite VSWR, any phase |
| RF Input for Rated Power Output |
0 dBm (1 milliwatt) CW/PEP, Max. |
| RF Input Overdrive (In-Band/Out-of-Band) |
+10 dBm, Max In-Band
+13 dBm, Max. Out-of-Band |
| RF Input Impedance |
50 Ohms, Nom. |
| RF Input VSWR |
1.5:1, Max |
| RF Input Signal Format |
CW, AM, Pulse, FM, Pulse |
| Harmonics at Full Forward Power Output |
-20 dBc, Min. |
| Spurious Signals (In-Band) at Rated Forward Power
Output |
-60 dBc, Min. |
| Protection |
Fully protected for overdrive, out-of-band operation;
output load VSWR and over temperature. |
| Stability |
Unconditionally stable, unit will not oscillate for any
condition of load and source impedance. |
| Display |
Status display, 3 digit, 7 segment, red LED and bar
display; absolute forward and reflected RF power, thermal fault and unleveled indication. |
| Connectors |
|
|
|
Type N, Female |
|
|
Type N, Female |
| Power Input |
3 wire IEC Type Male Connector |
| Cooling |
Forced air |
| Environmental |
|
- Operating Temperature Range
|
0 to 50 degrees C, Ambient |
|
|
-30 to +71 degrees C, Ambient |
|
|
10,000 feet, Max. |
|
|
95% Max with condensation |
|
|
Normal shock and vibration as encountered in truck
transportation. |
| Dimensions (19" rackmount) |
|
|
|
7"H x 20"D (17.8 cm x 50.8 cm) |
| Total Weight |
65 lbs. (29.5 kg) |
FRONT PANEL CONTROLS
POWER
Circuit breaker provides "ON"/"OFF" power
control and primary power protection of the amplifier system.
ALC (Automatic Level Control)
ALC push-button switch provides "ON"/"OFF"
control of the amplifier system internal ALC leveling loop. The illuminated position
indicated the active mode. On power turn-on, the amplifier system will always position
itself in the ALC "ON" and RF "ON" modes of operation.
ALC "ON" MODE
This mode provides operation of the amplifier system from its
own internal ALC loop.
ALC "OFF" MODE
In this mode, the amplifier can be used as a standard linear RF
amplifier up to the rated power output. Beyond its specified linear power output, internal
circuits will limit the amplifier to rated power output.
POWER LEVEL (10 TURN CONTROL)
Provides adjustment of the RF output power when operating in the
ALC "ON" mode. When the power level control is at maximum clockwise position,
the amplifier will provide rated-leveled RF power output. When the power level control is
fully counter-clockwise, the power is approximately –30 dB below rated power output
level.
FRONT PANEL DISPLAY
WATTS
3 digit, 7 segment, red LED numerical display indicates CW
forward/reverse RF power in watts.
FWD
Bar display (red LED) indicates forward RF power output is
displayed.
REV
Bar display (red LED) indicates reverse RF power output is
displayed. The PUSH FOR REV push-button switch must be depressed to read reverse RF
power output.
UNLEV
Bar display (red LED) indicator is active only when operating
the amplifier in the ALC "ON" mode. The display illuminates indicating an ALC
unleveled condition. This indicator is useful ONLY when the amplifier is operated in a
non-sweep operation (CW mode).
TEMP
Bar display (red LED) indicates an over-temperature condition in
the system. The amplifier system will automatically remove DC power to all bias circuits
should the condition occur. When the temperature reaches a safe operating condition, the
amplifier automatically resumes operation.
PUSH FOR REV
Depressing the PUSH FOR REV push-button switch displays
reverse RF power output. The REV bar display (red LED) illuminates indicating the active
mode.
RF
RF "ON"/"OFF" push-button switch provides
control of the amplifier system RF power output. Depressing the RF switch cycles the RF
output power on and off. The illuminated position indicates the active mode. This control
functions in both ALC modes.
RF "ON" MODE
This mode provides normal amplifier operation. On power turn-on,
the amplifier system always positions itself in the RF "ON" and ALC
"ON" modes of operation.
RF "OFF" MODE
In this mode, the amplifier internal voltage controlled pin
attenuator is positioned at maximum attenuation. (-60 dB, typical, below rated RF power
output)
MODULATION
Provides AM, pulse and square wave modulation of the internal
ALC loop when operating in the ALC "ON" mode. This modulation-input port is DC
coupled. Power output level must be adjusted for different modulation formats. The
amplifier cannot deliver more than rated CW/PEP power.