HW: PS300/ , 24MB mem
SW: RH6.2, RH6.2 Network Boot Disk "/images/bootnet.img"
24576 KB Detected
COMPAQ System BIOS - E15 (08/17/1998)
Copyright 1982,1998 Compaq Computer Corporation. All rights reserved.
Processor running at 150 MHz
SCSI Device Detected - System Board, SCSI ID 0: COMPAQ M1606S
SCSI Device Detected - System Board, SCSI ID 5: COMPAQ CRD-254V
SCSI Device Detected - System Board, SCSI ID 6: ARCHIVE 4326XX 27871-XXX
Insert the /images/bootnet.img floppy and boot to it:
Welcome to Red Hat Linux 6.2!
o To install or upgrade a system running Red Hat Linux 2.0
or later in graphical mode, press the key.
o To install or upgrade a system running Red Hat Linux 2.0
or later in text mode, type: text .
o To enable expert mode, type: expert . Press for
more information about expert mode.
o To enable rescue mode, type: linux rescue . Press
for more information about rescue mode.
o If you have a driver disk, type: linux dd .
o Use the function keys listed below for more information.
[F1-Main] [F2-General] [F3-Expert] [F4-Kernel] [F5-Rescue]
boot:
At the boot prompt, enter linux text expert mem=24M
boot: linux text expert mem=24M
Welcome to Red Hat Linux:
Devices: Insert your driver disk and press "OK" to continue. "OK" "CANCEL" -> "CANCEL"
Choose a Language: What language should be used during the installation process? -> English
Keyboard Type: What type of keyboard do you have? -> us
Installation Method: What type of media contains the packages to be installed? "NFS image" "FTP" "HTTP" -> "FTP"
Devices: Which driver should I try?... -> Amd PCnet32
Configure TCP/IP: Please enter the IP configuration for this machine. ... -> Use dynamic IP configuration.
FTP Setup: FTP site name: emperor
FTP Setup: Red Hat directory: pub/RedHat62/i386
Devices: I don't have any special device drivers loaded for your system. Would you like to load some now? "DONE" "ADD DEVICE" -> "ADD DEVICE"
Devices: What kind of device would you like to add "SCSI" "NETWORK" -> "SCSI"
Devices: Which driver should I try? ... -> Symbios/NCR 53C8xx
Devices: I have found the following devices in your system: "Symbios/NCR 53C8xx" "DONE" "ADD DEVICE" -> "DONE"
Red Hat Linux (C) 2000 Red Hat, Inc. Welcome
|----------------| Red Hat Linux |-----------------|
| |
| Welcome to Red Hat Linux! |
| |
| This installation process is outlined in detail |
| in the Official Red Hat Linux Installation |
| Guide available from Red Hat Software. If you |
| have access to this manual, you should read the |
| installation section before continuing. |
| |
| If you have purchased Official Red Hat Linux, |
| be sure to register your purchase through our |
| web site, http://www.redhat.com/. |
| |
| |--| |----| |
| |OK| |BACK| |
| |--| |----| |
| |
|--------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "OK"
Red Hat Linux (C) 2000 Red Hat, Inc. Installation Type
|--------------| Installation Type |---------------|
| |
| What type of system would you like to install? |
| |
| Install GNOME Workstation |
| Install KDE Workstation |
| Install Server System |
| Install Custom System |
| Upgrade Existing Installation |
| |
| |--| |----| |
| |OK| |BACK| |
| |--| |----| |
| |
|--------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "Install Custom System"
Red Hat Linux (C) 2000 Red Hat, Inc. Partition
|--------------------| Disk Setup |---------------------|
| |
| Disk Druid is a tool for partitioning and setting |
| up mount points. It is designed to be easier to use |
| than Linux's traditional disk partitioning software, |
| fdisk, as well as more powerful. However, there are |
| some cases where fdisk may be preferred. |
| |
| Which tool would you like to use? |
| |
| |------------| |-------| |------| |
| | Disk Druid | | fdisk | | Back | |
| |------------| |-------| |------| |
| |
|-------------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "fdisk"
Red Hat Linux (C) 2000 Red Hat, Inc. Manually Partition
|-----------------------| Disk Setup |------------------------|
| |
| To install Red Hat Linux, you must have at leaset one |
| partition of 150MB dedicated to Linux. We suggest placing |
| that partition on one of the first two hard drives in your |
| system so you can boot into Linux with LILO. |
| |
| /dev/sda - Compaq M1606S |
| |
| |------| |------| |------| |
| | Done | | Edit | | Back | |
| |------| |------| |------| |
| |
|-------------------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "Edit"
Command (m for help):p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda3 1 32 32752 12 Compaq diagnostics
Command (m for help):n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (33-1001, default 33): Press ENTER for default
Using default value 33
Last cylinder or +size or +sizeM or +sizeK (33-1001, default 1001): +30M
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 33 63 31744 83 Linux
/tmp/sda3 1 32 32752 12 Compaq diagnostics
Command (m for help):a
Partition number (1-4): 1
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 * 33 63 31744 83 Linux
/tmp/sda3 1 32 32752 12 Compaq diagnostics
Command (m for help):n
Command action
e extended
p primary partition (1-4)
e
Partition number (1-4): 2
First cylinder (64-1001, default 64): Press ENTER for default
Using default value 64
Last cylinder or +size or +sizeM or +sizeK (64-1001, default 1001): Press ENTER for default
Using default value 1001
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 * 33 63 31744 83 Linux
/tmp/sda2 64 1001 960512 5 Extended
/tmp/sda3 1 32 32752 12 Compaq diagnostics
Command (m for help):n
Command action
l logical (5 or over)
p primary partition (1-4)
l
First cylinder (64-1001, default 64): Press ENTER for default
Using default value 64
Last cylinder or +size or +sizeM or +sizeK (64-1001, default 1001): +200M
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 * 33 63 31744 83 Linux
/tmp/sda2 64 1001 960512 5 Extended
/tmp/sda3 1 32 32752 12 Compaq diagnostics
/tmp/sda5 64 264 205808 83 Linux
Command (m for help):t
Partition number (1-5): 5
Hex code (type L to list codes): 82
Changed system type of partition 5 to 82 (Linux swap)
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 * 33 63 31744 83 Linux
/tmp/sda2 64 1001 960512 5 Extended
/tmp/sda3 1 32 32752 12 Compaq diagnostics
/tmp/sda5 64 264 205808 82 Linux swap
Command (m for help):n
Command action
l logical (5 or over)
p primary partition (1-4)
l
First cylinder (265-1001, default 265): Press ENTER for default
Using default value 265
Last cylinder or +size or +sizeM or +sizeK (265-1001, default 1001): Press ENTER for default
Using default value 1001
Command (m for help): p
Disk /tmp/sda: 64 heads, 32 sectors, 1001 cylinders
Units = cylinders of 2048 * 512 bytes
Device Boot Start End Blocks Id System
/tmp/sda1 * 33 63 31744 83 Linux
/tmp/sda2 64 1001 960512 5 Extended
/tmp/sda3 1 32 32752 12 Compaq diagnostics
/tmp/sda5 64 264 205808 82 Linux swap
/tmp/sda6 265 1001 754672 83 Linux
Command (m for help):w
The partition table has been altered!
...
Red Hat Linux (C) 2000 Red Hat, Inc. Manually Partition
|-----------------------| Disk Setup |------------------------|
| |
| To install Red Hat Linux, you must have at leaset one |
| partition of 150MB dedicated to Linux. We suggest placing |
| that partition on one of the first two hard drives in your |
| system so you can boot into Linux with LILO. |
| |
| /dev/sda - Compaq M1606S |
| |
| |------| |------| |------| |
| | Done | | Edit | | Back | |
| |------| |------| |------| |
| |
|-------------------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "Done"
Red Hat Linux (C) 2000 Red Hat, Inc. Partition
|-------------------------| Current Disk Partitions |--------------------------|
| Mount Point Device Requested Actual Type |
| sda1 31M 31M Linux native |
| sda3 31M 31M Compaq Setup |
| sda5 200M 200M Linux swap |
| sda6 736M 736M Linux native |
| |
| Drive Summaries |
| Drive Geom [C/H/S] Total Used Free |
| sda [ 1001/ 64/32] 1001M 1001M 1M [##########] |
| |
| |------| |----| |------| |
| | Edit | | Ok | | Back | |
| |------| |----| |------| |
| |
|------------------------------------------------------------------------------|
F3-Edit F12-Ok v 1.00
Specify mount points for each of the Linux partitions:
sda1 -> /boot
sda6 -> /
Red Hat Linux (C) 2000 Red Hat, Inc. Partition
|-------------------------| Current Disk Partitions |--------------------------|
| Mount Point Device Requested Actual Type |
| /boot sda1 31M 31M Linux native |
| sda3 31M 31M Compaq Setup |
| sda5 200M 200M Linux swap |
| / sda6 736M 736M Linux native |
| |
| Drive Summaries |
| Drive Geom [C/H/S] Total Used Free |
| sda [ 1001/ 64/32] 1001M 1001M 1M [##########] |
| |
| |------| |----| |------| |
| | Edit | | Ok | | Back | |
| |------| |----| |------| |
| |
|------------------------------------------------------------------------------|
F3-Edit F12-Ok v 1.00
-> "Ok"
Red Hat Linux (C) 2000 Red Hat, Inc. Swap
|-----------------| Low Memory |------------------|
| |
| As you don't have much memory in this machine, |
| we need to turn on swap space immediately. To |
| do this we'll have to write your new partition |
| table to the disk immediately. Is that okay? |
| |
| |-----| |----| |
| | Yes | | No | |
| |-----| |----| |
| |
|-------------------------------------------------|
<Tab>/<Alt-Tab> between elements | <Space> selects | <F12> next screen
-> "Yes"
Filesystem Formatting:
Choose Partitions to Format: what partitions would you like to format? ... -> select all partitions.
"OK"
LILO Configuration:
LILO Configuration: A few systems will need to pass special options to the kernel at boot time for the system to function properly. If yo need to pass boot options to the kernel, enter them now. If you don't need any or aren't sure, leave this blank. -> turn off linear mode, add the following:
mem=24M
"OK"
LILO Configuration: Where do you want to install the bootloader? "MBR" "First sector of boot partition" -> First sector of boot partition
"OK"
LILO Configuration: The boot manager Red Hat uses can boot other operating systems as well. You need to tell me what partitions you would like to be able to boot and what label you want to use for each of them. -> "OK"
Video Card Selection: Which video card do you have? -> Unlisted Card
X Server Selection: Choose a server -> SVGA
Installation Begins:
Installation to begin: A complete log of your installation will be in /tmp/install.log after rebooting yoru system. You may want to keep this file for later reference. "OK" "BACK" -> "OK"
302 packages, 360MB, Total Time for File Copy=42 minutes
Boot Disk:
Bootdisk: A custom boot disk provides a way of booting into your Linux system without depending on the normal bootloader. ... Would you like to create a boot disk for your system? -> "YES"
Bootdisk: Insert a blank floppy in the first floppy drive. All data on this disk will be erased during creation of the boot disk. -> "OK"
Xconfigurator 4.3.5:
Monitor Setup: What type of monitor do you have? -> "CUSTOM"
Custom Monitor Setup: Now we want to set the specifications of the monitor. ... -> "OK"
Custom Monitor Setup (Continued): You must indicate the horizontal sync range of your monitor. ... -> "Non-Interlaced SVGA, 1024X768 @ 60 Hz, 800x600 @ 72 Hz"
Custom Monitor Setup (Continued): You must indicate the vertical sync range of your monitor. ... -> "50-90"
Screen Configuration: Xconfigurator now needs to setup the default resolution and color depth. ... -> "PROBE"
Probing to begin: Xconfigurator will now run the X server you selected to probe various information about your video card. It is normal for the screen to blink several times. -> "OK"
Probing finished:
Xconfigurator has successfully probed your video card. The default video mode will be:
Color Depth: 8 bits per pixel
Resolution : 800x600
Do you want to accept this setting, or select for yourself?
"USE DEFAULT" "LET ME CHOOSE" "BACK"
-> "USE DEFAULT"
Starting X: Xconfigurator will now start X to test your configuration. "OK" "SKIP" -> "OK"
Can you see this message? Automatic timeout in 10 seconds. "YES" "NO" -> "YES"
Xconfigurator can set up you computer to automatically start X upon booting. Would you like X to start when you reboot? "YES" "NO" -> "NO"
Installation Complete:
Red Hat Linux (C) 2000 Red Hat, Inc. Installation Complete
Complete:
Congratulations, installation is complete.
Press return to reboot, and be sure to remove
your boot medium as the system reboots, or your
system will return to the install. For information
on fixes which are available for this release
of Red Hat Linux, consult the Errata available
from http://www.redhat.com/errata.
Information on configuring and using your red
Hat Linux system is contained in the Red Hat
Linux manuals.
"OK"
-> "OK"
install exited abnormally -- received signal 11
sending termination signals...done
sending kill signals...done
disabling swap...
/tmp/swap/sda5
unmounting filesystems...
/mnt/runtime
/dev/pts
/proc
you may safely reboot your system
"Reboot"
24576 KB Detected
COMPAQ System BIOS - E15 (08/17/1998)
Copyright 1982,1998 Compaq Computer Corporation. All rights reserved.
Processor running at 150 MHz
SCSI Device Detected - System Board, SCSI ID 0: COMPAQ M1606S
SCSI Device Detected - System Board, SCSI ID 5: COMPAQ CRD-254V
SCSI Device Detected - System Board, SCSI ID 6: ARCHIVE 4326XX 27871-XXX
Press "F10" key for System Partition Utilities
Missing operating system
Boot disk worked ok. Probably MBR is corrupt, will run "fdisk /mbr" from Win95 boot disk.
fdisk /mbr didn't work, will check that /boot is marked active.
/boot is marked active - will put LILO out again on /boot.
Check /etc/lilo.conf, found that the following line is incorrect
